If you have a flat tire

Your vehicle is equipped with a spare tire. The flat tire can be replaced with the spare tire.

For details about tires: Tires

Warning:

Do not continue driving with a flat tire.Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair, which could result in an accident.

Before repairing the tire

Stop the vehicle in a safe place on a hard, flat surface.

Set the parking brake.

Shift the shift lever to P.

Stop the hybrid system.

Turn on the emergency flashers. (Operating instructions)

Tools

Spare tire Storage location Location of the spare tire, jack and tools

Spare tire, jack and tools

Spare tire

Jack

Tool bag

Warning:

Using the tire jack

Observe the following precautions.

Improper use of the tire jack may cause the vehicle to suddenly fall off the jack, leading to death or serious injury.

Do not use the tire jack for any purpose other than replacing tires or installing and removing tire chains.

Only use the tire jack that comes with this vehicle for replacing a flat tire.Do not use it on other vehicles, and do not use other tire jacks for replacing tires on this vehicle.

Put the jack properly in its jack point.

Do not put any part of your body under the vehicle while it is supported by the jack.

Do not start the hybrid system or drive the vehicle while the vehicle is supported by the jack.

Do not raise the vehicle while someone is inside.

When raising the vehicle, do not put an object on or under the jack.

Do not raise the vehicle to a height greater than that required to replace the tire.

Use a jack stand if it is necessary to get under the vehicle.

When lowering the vehicle, make sure that there is no-one near the vehicle. If there are people nearby, warn them vocally before lowering.

Using the jack handle

Insert the square head securely until you hear a click to prevent the extension parts from coming apart unexpectedly.

Wheel lock nut

Wheels Wheel lock nut Wheel lock nut (if equipped)

When replacing tires on a vehicle with wheel lock nuts, use the following procedures to remove and install the wheel lock nuts. The wheel lock key is stored in the glove box. Always return the wheel lock key to its original position after use, so that it does not get lost. (Location of the spare tire, jack and tools)

Removal

For ease of removal, the wheel lock nut should always be the first one loosened.

Place the wheel lock key on top of the wheel lock nut, turning until the wheel lock key and wheel lock nut patterns engage.

Place the wheel nut wrench on the wheel lock key, and while applying pressure on the wheel lock key, loosen the wheel lock nut.

Installation

For ease of installation, the wheel lock nut should always be the last one tightened.

By hand, install a wheel lock nut on each wheel.

Place the wheel lock key on top of the wheel lock nut, turning until the wheel lock key and wheel lock nut patterns engage.

Place the wheel nut wrench on the wheel lock key, and while applying pressure on the wheel lock key, tighten the wheel lock nut to the recommended torque.

Notice:

When using a wheel lock key (if equipped)

Do not use an impact wrench. Using an impact wrench may cause permanent damage to wheel lock nut and wheel lock key. If in doubt about wheel lock application, contact your Toyota dealer.

Taking out the jack

Remove the cover.

Unhook the rubber strap, and take out the jack.

Loosen

Tighten

After using the jack, install the jack in the exact reverse order from which it was removed. Also, the jack should be properly secured using a rubber strap.

Taking out the tool bag

Lift the deck board.

Lift the side deck board.

Take out the tool bag.

Taking out the spare tire

Assemble the jack handle extension as shown.

Remove the cover.

To protect the bodywork, place a rag between the screwdriver and the vehicle body as shown in the illustration.

Insert the end of the jack handle extension into the lowering screw and turn it counterclockwise.

After the tire is lowered completely to the ground, remove the holding bracket.

Replacing a flat tire

Chock the tires.


Tire	Wheel chock positions
Front left-hand side	Behind the rear right-hand side tire
Front right-hand side	Behind the rear left-hand side tire
Rear left-hand side	In front of the front right-hand side tire
Rear right-hand side	In front of the front left-hand side tire

Slightly loosen the wheel nuts (one turn).

Vehicles with wheel locks:Use the wheel lock key to loosen the wheel lock.

Assemble the jack handle extension as shown.

Position the jack at the correct jack point as shown.

Front

Rear

Make sure the jack is positioned on a level and solid place.

Raise the vehicle until the tire is slightly raised off the ground.

When positioning the jack under the rear axle housing, make sure the groove on the top of the jack fits with the rear axle housing.

Remove all the wheel nuts and the tire.

When resting the tire on the ground, place the tire so that the wheel design faces up to avoid scratching the wheel surface.

Warning:

Replacing a flat tire

Observe the following precautions.

Failure to do so may result in serious injury:

Lower the spare tire completely to the ground before removing it from under the vehicle.

Do not try to remove the wheel ornament by hand. Take due care in handling the ornament to avoid unexpected personal injury.

Do not touch the disc wheels or the area around the brakes immediately after the vehicle has been driven. After the vehicle has been driven the disc wheels and the area around the brakes will be extremely hot. Touching these areas with hands, feet or other body parts while changing a tire, etc., may result in burns.

Failure to follow these precautions could cause the wheel nuts to loosen and the tire to fall off, resulting in death or serious injury.

Never use oil or grease on the wheel bolts or wheel nuts.Oil and grease may cause the wheel nuts to be excessively tightened, leading to bolt or disc wheel damage. Remove any oil or grease that has adhered when installing the wheel nuts.

After replacing a tire, check the tightening torque as soon as possible.

Steel wheel: 154 ft•lbf (209 N•m, 21.3 kgf•m)Aluminum wheel: 97 ft•lbf (131 N•m, 13.4 kgf•m)

When installing a tire, only use wheel nuts that have been specifically designed for that wheel.

Retighten the wheel nuts within 100 miles (160 km) of driving.

If there are any cracks or deformations in the bolt screws, nut threads or bolt holes of the wheel, have the vehicle inspected by your Toyota dealer.

Do not attach a heavily damaged wheel ornament, as it may fly off the wheel while the vehicle is moving.

When installing the wheel nuts, be sure to install them with the tapered ends facing inward.

Replacing a flat tire for vehicles

In cases such as when replacing tires, make sure to cancel the power back door system. (Changing settings of the power back door system (vehicles with power back door)) Failure to do so may cause the back door to operate unintentionally if the power back door switch is accidentally touched, resulting in hands and fingers being caught and injured.

Installing the spare tire

Remove any dirt or foreign matter from the wheel contact surface.

If foreign matter is on the wheel contact surface, the wheel nuts may loosen while the vehicle is in motion, causing the tire to come off.

Install the spare tire and loosely tighten each wheel nut by hand by approximately the same amount.

When replacing an aluminum wheel with a steel wheel (including a compact spare tire), tighten the wheel nuts until the tapered portion comes into loose contact with the disc wheel seat .

When replacing an aluminum wheel with a spare aluminum wheel, tighten the nuts until the washer of the nut comes into loose contact with the disc wheel .

Lower the vehicle.

Securely tighten the wheel nuts two or three times in the order shown in the illustration using a wheel nut wrench.

Vehicles with wheel locks:Tighten the wheel lock using the wheel lock key after tightening the other wheel nuts.

Tightening torque:Steel wheel: 154 ft•lbf (209 N•m, 21.3 kgf•m)Aluminum wheel: 97 ft•lbf (131 N•m, 13.4 kgf•m)

Stowing the flat tire, jack and all tools

Remove the center wheel ornament by pushing from the reverse side.

Lay down the tire with the valve stem facing up and install the holding bracket.Turn the jack handle extension clockwise to take up slack in the chain.

Check to ensure the holding bracket is centered in the wheel hub.

While raising, secure the tire, taking care that the tire goes straight up without catching on any surrounding parts, to prevent it from flying forward during a collision or sudden braking.

Tightening torque:34.7 ft•lbf (46.6 N•m, 4.8 kgf•m)

Confirm it is not loose after tightening:

Push and pull the tire

Try rotating

Visually check to ensure tire is not hung on surrounding parts.

If looseness or misassembly exists, repeat step 2 and step 4.

Repeat step 5, any time the tire is lowered or disturbed.

Stow the tools and jack securely.

Note:

The compact spare tire (Vehicles with a compact spare tire)

The compact spare tire is identified by the “ TEMPORARY USE ONLY” marking on the disc wheel and/or tire sidewall.Use the compact spare tire temporarily, and only in an emergency.

Make sure to check the tire inflation pressure of the compact spare tire. (Tires and wheels)

When using the compact spare tire (Vehicles with a compact spare tire)

As the compact spare tire is not equipped with the tire pressure warning valve and transmitter, low inflation pressure of the spare tire will not be indicated by the tire pressure warning system. Also, if you replace the compact spare tire after the tire pressure warning light comes on, the light remains on.

When the compact spare tire is equipped (Vehicles with a compact spare tire)

When driving with the compact spare tire installed, the vehicle height will be different than when driving with standard tires.

If you have a flat rear tire on a road covered with snow or ice (Vehicles with a compact spare tire)

Install the compact spare tire on one of the front wheels of the vehicle. Perform the following steps and fit tire chains to the rear tires:

Replace a front tire with the compact spare tire.

Replace the flat rear tire with the tire removed from the front of the vehicle.

Fit tire chains to the rear tires.

Warning:

When using the compact spare tire (Vehicles with a compact spare tire)

Remember that the compact spare tire provided is specifically designed for use with your vehicle. Do not use your compact spare tire on another vehicle.

Do not use more than one compact spare tires simultaneously.

Replace the compact spare tire with a standard tire as soon as possible.

Avoid sudden acceleration, abrupt steering, sudden braking and shifting operations that cause sudden engine braking.

When the compact spare tire is attached (Vehicles with a compact spare tire)

The vehicle speed may not be correctly detected, and the following systems may not operate correctly:

ABS & Brake assist

VSC

TRAC

PCS (Pre-Collision System)

AHB (Automatic High Beam)

LTA (Lane Tracing Assist)

LDA (Lane Departure Alert)

Dynamic radar cruise control

Cruise control

EPS

Trailer Sway Control

Tire pressure warning system

Panoramic view monitor (if equipped)

Multi-terrain Monitor (if equipped)

Toyota parking assist monitor (if equipped)

PKSB (Parking Support Brake)

Navigation system (if equipped)

Also, not only can the following system not be utilized fully, but it may even negatively affect the drive-train components:

4WD system

Speed limit when using the compact spare tire (Vehicles with a compact spare tire)

Do not drive at speeds in excess of 50 mph (80 km/h) when a compact spare tire is installed on the vehicle.

The compact spare tire is not designed for driving at high speeds. Failure to observe this precaution may lead to an accident causing death or serious injury.

Stowing the flat tire

Failure to follow steps listed under stowing the tire may result in damage to the spare tire carrier and loss of the tire, which could result in serious injury or death.

Never use an impact wrench to turn the spare tire clamp bolt.Failure to follow this precaution could cause the tire to fall off while driving, resulting in death or serious injury.

After using the tools and jack

Before driving, make sure all the tools and jack are securely in place in their storage location to reduce the possibility of personal injury during a collision or sudden braking.

Notice:

Be careful when driving over bumps with the compact spare tire installed on the vehicle (Vehicles with a compact spare tire)

The vehicle becomes lower when driving with the compact spare tire compared to when driving with standard tires. Be careful when driving over uneven road surfaces.

Do not drive the vehicle with a flat tire

Do not continue driving with a flat tire.Driving even a short distance with a flat tire can damage the tire and the wheel beyond repair.

When stowing the flat tire

Ensure that there is no object caught between the tire and the vehicle underbody.

When replacing the tires

When removing or fitting the wheels, tires or the tire pressure warning valve and transmitter, contact your Toyota dealer as the tire pressure warning valve and transmitter may be damaged if not handled correctly.

To avoid damage to the tire pressure warning valves and transmitters

When a tire is repaired with liquid sealants, the tire pressure warning valve and transmitter may not operate properly. If a liquid sealant is used, contact your Toyota dealer or other qualified service shop as soon as possible. Make sure to replace the tire pressure warning valve and transmitter when replacing the tire. (Installing tire pressure warning valves and transmitters)