Other interior features USB Type-C charging portUSB Type-C charging ports The USB Type-C charging ports are used to supply electricity to external devices. Use the appropriate terminal for each charging port type.The USB Type-C charging ports are for charging only.They are not designed for data transfer or other purposes.Depending on the external device, it may not charge properly.Refer to the manual included with the device before using a USB Type-C charging port. Using the USB Type-C charging ports On the instrument panel These USB Type-C charging ports are capable of high power output. An output up to 45 W max on a single port or 52.5 W combined (shared) is possible. The USB Type-C charging ports operate at multiple voltage and multiple wattage levels. Rear of console box The USB Type-C charging ports are used to supply 3.0 A of electricity at 5 V to external devices. Note: The USB Type-C charging ports can be used when The power switch is in ACC or ON, or the multimedia system is on. Situations in which the USB Type-C charging ports may not operate correctly Rear of console box: If a device which consumes more than 3.0 A at 5 V is connected If a device designed to communicate with a personal computer, such as a USB memory device, is connected If the connected external device is turned off (depending on device) If the temperature inside the vehicle is high, such as after the vehicle has been parked in the sun About connected external devices Depending on the connected external device, charging may occasionally be suspended and then start again. This is not a malfunction. Notice: To prevent damage to the USB Type-C charging ports Do not insert foreign objects into the ports. Do not spill water or other liquids into the ports. Do not apply excessive force to or impact the USB Type-C charging ports. Do not disassemble or modify the USB Type-C charging ports. To prevent damage to external devices Do not leave external devices in the vehicle. The temperature inside the vehicle may become high, resulting in damage to an external device. Do not push down on or apply unnecessary force to an external device or the cable of an external device while it is connected. To prevent 12-volt battery discharge Do not use the USB Type-C charging ports for a long period of time with the hybrid system is off. Wireless chargerWireless charger A portable device can be charged by just placing Qi standard wireless charge compatible portable devices according to the Wireless Power Consortium, such as smartphones and mobile batteries, etc., on the charge area. The compatible portable devices can be found on the following Wireless Power Consortium website.https://www.wirelesspowerconsortium.com/ This function cannot be used with portable devices that are larger than the charging tray. Also, depending on the portable device, it may not operate as normal. Please read the operation manual for portable devices to be used. The “ Qi” logo The “ Qi” logo is a trademark of the Wireless Power Consortium. Name for all parts Operation indicator light Charging area* Charging tray Approximately 1.0 in. (2.5 cm) Approximately 3.9 in. (10 cm) *Compatible portable devices and the wireless charger contain charging coils. The charging coil in the wireless charger can be moved within the charge area up to the position of the charging coil inside a portable device. Charging is possible if the center of the coil of the portable device is placed within the charge area.If 2 or more portable devices are placed on the charging tray, their charging coils may not be properly detected and they may not be charged. Using the wireless charger Place the portable device on the charging tray. Place the charging side of the portable device down with the center of the device in the center of the charge area. When charging, the operation indicator light (orange) comes on. If charging is not occurring, refer to “Situations in which the function may not operate normally” (Situations in which the function may not operate normally). When charging is complete, the operation indicator light (green) comes on. Recharging function When charging is complete and after a fixed time in the charge suspension state, charging restarts. When a portable device is moved significantly in the charge area, the charging coil is disconnected and charging is stopped momentarily. However, if there is a charging coil in the charge area, the charging coil inside the wireless charger will move toward it and then charging restarts. Rapid charging function The following portable devices support rapid charging. Portable devices compliant with WPC Ver1.3.2 and compatible with rapid charging iPhone’s with an iOS version that supports 7.5 W charging (iPhone 8 and later models) Portable devices compatible with Galaxy original rapid charging standard. When a portable device that supports rapid charging is charged, charging automatically switches to the rapid charging function. Lighting conditions of operation indicator light
Operation indicator light Conditions
Charging tray side Multimedia system screen side
Turning off Disappear When the Multimedia power supply is off or power switch is off
Green (comes on) Gray On Standby (charging possible state)*1
When charging is complete*2
Orange (comes on) Blue Charging
*1Charging power will not be output during standby. A metallic object will not be heated, if it is placed on the charging tray in this state. *2Depending on the portable device, there are cases where the operation indicator light will continue being lit up orange even after the charging is complete. The wireless charger is not working properly The following are situations in which the wireless charger does not work properly and how to deal with the possible causes.
Operation indicator light Multimedia system screen Suspected causes/Handling method
Orange (Flashing repeatedly once every second) Gray Vehicle to wireless charger communication failure If the hybrid system is operating, stop and then restart the hybrid system. If the power switch is in ACC, start the hybrid system. (Starting the hybrid system)
Green (Flashing repeatedly once every second) Disappear Wireless charger and multimedia system communication failure If the hybrid system is operating, stop and then restart the hybrid system. If the power switch is in ACC, start the hybrid system. (Starting the hybrid system)
Green (comes on) Blue AM radio stations are being automatically selected Wait until the system has completed the automatic selection of AM radio stations. In the case that automatic selection cannot be completed, stop automatic selection.
The smart key system is detecting the key Wait until the key detection is complete.
Green (comes on) Gray Foreign substance detection:A metallic foreign substance is in the charge area, and so the abnormal heating prevention function of the metallic foreign substance operated Remove the foreign substance from the charge area.
Portable device misaligned/distanced from charging surface:The center of charging coil in the portable device moved outside of the charging area, or lens convex is large, or case is thick so the abnormal heating prevention function operated Remove the portable device from the wireless charger, after 5 seconds, then place the portable device so that it is near the center of the wireless charger.Also, if a case or cover is installed to the portable device, remove it.
Battery protection function of portable device:Before full charging, battery protection function of portable device operated Confirm the setting of portable device. Continued detection of an electronic key:When a Multimedia function is used through vehicle customization, the electronic key is continually detected without being confirmed. In this case, turn the power switch ACC or ON to confirm the key.
Orange (Repeatedly flashes 4 times continuously) Gray Safety shutdown resulting when the temperature within the wireless charger exceeded the set value Stop charging, remove the portable device from the charging tray, wait for the temperature to drop, and then start charging again.
Note: The wireless charger can be operated when The power switch is in ACC or ON, or the multimedia system is on. Usable portable devices Qi standard wireless charge standard can be used on compatible devices. However, compatibility with portable devices that comply with Qi Ver. 1.0, 1.3.2 and later versions, and Qi2 MPP (Magnet Power Profile) is not guaranteed. Starting with mobile phones and smartphones, it is aimed for low power electrically supplied portable devices of no more than 5 W. However, charging exceeding 5 W is supported by the following portable devices. Charging at 7.5 W or less is supported by iPhone’s that support 7.5 W charging. Charging at 10 W or less is supported by Galaxy device that support 10 W charging of original standard. Charging at 15 W or less is supported by portable devices compliant with EPP output as defined by WPC standard Ver1.3.2. Using the smart key system If the smart key system detects the electronic key while a device is being charged, charging will be temporarily stopped. When the electronic key is detected, charging will automatically start again. When covers and accessories are attached to portable devices Do not charge in situations where cover and accessories not able to handle Qi are attached to the portable device. Depending on the type of cover (including for certain genuine manufacturer parts) and accessory, charging may not be possible. In addition, Qi2 is not supported. As a result, charging may not be possible when an accessory and cover that comply with Qi2 are installed. When charging is not performed even with the portable device placed on the charge area, remove the cover and accessories. AM radio cooperation function during charging During charging, if noise occurs when listening to the AM radio, the charging frequency is automatically changed to reduce the noise. When automatically seeking AM radio stations, charging will be suspended to prevent charging noise from being detected as a radio station. Charging will resume automatically when seek tuning is stopped. Important points of the wireless charger If the electronic key cannot be detected within the vehicle interior, charging can not be done. When the door is opened and closed, charging may be temporarily suspended. When charging, the wireless charging device and portable device will get warmer, however this is not a malfunction. When a portable device gets warm while charging, charging may stop due to the protection function on the portable device side. In this case, when the temperature of the portable drops significantly, charge again.The fan may start operating to lower the temperature inside the wireless charger, however this is not a malfunction. Operation sounds A buzzing noise may be heard when pressing the power switch to turn to ACC or ON or when detecting a portable device. However, this is not a malfunction. Cleaning the wireless charger Cleaning the interior (especially instrument panel) Situations in which the function may not operate normally Devices may not be charged normally in the following situations. The portable device is fully charged The portable device is being charged with a cable connected There is foreign matter between the charge area and portable device Charging has caused the portable device to heat up The temperature around the charging tray is 95°F (35°C) or higher, such as in extreme heat The portable device is placed with its charging surface facing up The small portable device such as foldable type is placed in an area misaligned from the charge area The portable device is larger than the charging tray The camera lens protrudes 0.12 in (3 mm) or more from the surface of the portal device The vehicle is in an area where strong electrical waves or noise are emitted, such as near a television tower, power plant, gasoline station, broadcasting station, large display, airport, etc. The electronic key is not inside the vehicle Any of the following objects is stuck or installed between the charging side of the portable device and the charge area. Thick cases or covers A case or cover attached with an uneven or tilted surface, so that the charging side is not flat Thick decorations Accessories, such as finger rings,a.straps, etc. Cover to protect camera lens When there is a gap between the charging side of the portable device and the charge area due to a protrusion such as a camera on the charging side of the portable device. When the portable device is in contact with, or is covered by any of the following metallic objects: A card that has metal on it, such as aluminum foil, etc. A pack of cigarettes that includes aluminum foil A wallet or bag that is made of metal Coins A heating pad CDs, DVDs or other media A metal accessory A case or cover made of metal A flip type case with a magnet on the charging side of the portable device Electric wave type wireless remote controls are being used nearby 2 or more portable devices are placed on the charging tray at the same time If you use a device with a built-in S-Pen (Galaxy Note series, etc.) and the device with the S-Pen inserted is on the tray. If charging is abnormal or the operation indicator light continues to flash for any other reason, the wireless charger may be malfunctioning. Contact your Toyota dealer. If the smartphone OS has been updated If the smartphone OS has been updated to a newer version, its charging specifications may have changed significantly.For details, check the information on the manufacturer’s website. Trademark information iPhone is a trademark of Apple Inc., registered in the U.S. and other countries. “ Galaxy” is a trademark or registered trademark of Samsung Electronics Co., Ltd. Certification Wireless charger Warning: Caution while driving When charging a portable device, for safety reasons, the driver should not operate the main part of the portable device while driving. Caution while in motion Do not charge lightweight devices such as wireless headphones while in motion. These devices are very light and may be ejected from the charging tray, which may lead to unforeseen accidents. Caution regarding interference with electronic devices People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverters, as well as any other electrical medical device, should consult their physician about the usage of the wireless charger. To prevent malfunctions or burns Observe the following precautions. Failure to do so may result in a equipment failure and damage, catch fire, burns due to overheat or electric shock. Do not insert any metallic objects between the charge area and the portable device while charging Do not attach an aluminum sticker or other metallic object to the charge area Do not attach an aluminum sticker or other metallic object to the side of the portable device (or to its case or cover) that touches the charge area Do not use the charging tray as a small storage space Do not subject to a strong force or impact Do not disassemble, modify or remove Do not charge devices other than specified portable devices Keep away from magnetic items Do not perform charging if the charging area is dirty Do not cover with a cloth or similar material Notice: To prevent malfunctions and data corruptions When charging, bringing a credit, or other magnetic card, or magnetic storage media close to the charge area may clear any stored data due to magnetic influence. Furthermore, the electronic key may not operate due to magnetic interference if the electronic key for the vehicle is placed on the mobile phone terminal while charging or an open space. Also, do not bring a wristwatch or other precision instrument close to the charge area since doing so may cause it to malfunction. Do not charge with a non-contact IC card such as a transportation system IC card inserted between the charging side of a portable device and the charge area. The IC chip may become extremely hot and damage the portable device or IC card. Be especially careful not to charge a portable device inside a case or cover with a non-contact IC card attached. Do not leave portable devices inside the vehicle. The inside of the vehicle can become hot in extreme heat, which could cause a malfunction. To prevent 12-volt battery discharge Do not use the wireless charger for a long period of time when the hybrid system is stopped. ArmrestArmrest Pull the armrest down for use. Notice: To prevent damage to the armrest Do not place too much strain on the armrest. Assist gripsAssist grips Type A An assist grip installed on the ceiling can be used to support your body while sitting on the seat. Type B An assist grip installed on the pillar can be used when getting in or out of the vehicle and others. Warning: Assist grips (type A) Do not use the assist grip when getting in or out of the vehicle or rising from your seat. Notice: To prevent damage to the assist grip Do not hang any heavy object or put a heavy load on the assist grip. Coat hooksCoat hooks Warning: Items that must not be hung on the hook Do not hang a coat hanger or other hard or sharp object on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles that cause death or serious injury. Power outletPower outlet (12 VDC) The power outlet can be used for 12 V accessories that run on less than 10 A. Open the lid. Note: The power outlet can be used when The power switch is in ACC or ON, or the multimedia system is on. When stopping the hybrid system Disconnect electrical devices with charging functions, such as mobile battery packs. If such devices are left connected, the hybrid system may not stop normally. Notice: To avoid damaging the power outlet Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit. To prevent the fuse from being blown Do not use an accessory that uses more than 12 V 10 A. To prevent 12-volt battery discharge Do not use the power outlet longer than necessary when the hybrid system is off. Sun visorsSun visors To set the visor in the forward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side. To use the side extender, place the visor in the side position, then slide it backward. Vanity mirrors Vanity lights Mirrors Vanity mirrors Lights Vanity lights Vanity mirrors Open the cover. The vanity light turns on. Note: To prevent 12-volt battery discharge If the vanity lights remain on when the power switch is turned off, the lights will go off automatically after 20 minutes. Notice: To prevent the 12-volt battery from being discharged Do not leave the vanity lights on for extended periods while the hybrid system is off. Auxiliary switchesAuxiliary switches (if equipped) When the Toyota Genuine Accessories Pre-wired Auxiliary Switches* is connected to the vehicle, a 12V DC powered circuit is available for switch operation. In addition to the 12V DC power circuit operated by a switch, there is also a 12V DC power circuit that constantly supplies power when the power switch for the vehicle is turned on. There are four auxiliary switches that provide power to connectors in multiple locations where electrical accessories can be used. Remove the waterproof cap (if present) from vehicle wire harness connector to connect accessory wiring harness pigtail. The auxiliary switch will only operate in the power switch to ON. When an aux switch is pressed, the indicator on the switch will illuminate. If the vehicle’s power usage increases and the 12-volt battery voltage becomes low, the auxiliary switch system may automatically turn off. The system will turn on again when the vehicle power usage is reduced and the 12-volt battery voltage increases. *Accessory wire harness pigtails can be purchased at your Toyota dealer. AUX1 AUX2 AUX3 AUX4 Location of auxiliary switch wire harness connectors: Engine compartment Cabin Engine compartment Powered Circuits:
Circuit Fuse Name Fuse Size Fuse Location Pigtail Wire Color Connector Location
AUX1 AUX NO.1 40A Engine compartment Blue Engine compartment
40A Ground Brown
AUX2 AUX NO.2 20A Engine compartment Red
20A Ground Black/White
AUX3 AUX NO.3 15A Engine compartment Black Engine compartment , cabin
AUX4 AUX NO.4 10A Green
Power switch ON* AUX NO.5 10A White
Common Ground Black/White
*“ IGNITION ON” will be displayed on the meter. Warning: For safe use Do not cut or modify the wiring harness of the vehicle body when connecting accessory electronics. Failure to do so may lead to an accident resulting in property damage, serious injury, or death. Notice: To prevent damage to the auxiliary switches For information on repairs, contact your Toyota dealer. Accessory wiring harness pigtails can be purchased from your Toyota dealer.