Other interior features Sun visorsSun visors To set the visor in the forward position, flip it down. To set the visor in the side position, flip down, unhook, and swing it to the side. To use the side extender (if equipped), place the visor in the side position, then slide it backward. Vanity mirrors Vanity lights Vanity lights Mirrors Vanity mirrors Lights Vanity lights Vanity mirrors Slide the cover to open. The light turns on when the cover is opened. Note: Automatic light off to prevent 12-volt battery discharge If the vanity lights remain on when the power switch is turned to OFF, the lights will go off automatically after 10 minutes. Notice: To prevent 12-volt battery discharge Do not leave the vanity lights on for extended periods while the hybrid system is off. Power outletPower outlet Please use a power supply for electronic goods that use less than 12 VDC /10 A (power consumption of 120 W). When using electronic goods, make sure that the power consumption of all the connected power outlets is less than 120 W. Console box Open the console box and open the lid. Luggage compartment (if equipped) Open the lid. Note: The power outlet can be used when The power switch is in ACC or ON, or the multimedia system is on. When stopping the hybrid system Disconnect electrical devices with charging functions, such as mobile battery packs.If such devices are left connected, the hybrid system may not stop normally. Notice: When power outlet is not in use To avoid damaging the power outlet, close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit. To prevent blown fuse Do not use an accessory that uses more than 12 V 10 A. To prevent 12-volt battery discharge Do not use the power outlet longer than necessary when the hybrid system is off. USB Type-C charging portsUSB Type-C charging ports The USB Type-C charging ports are used to supply 3 A of electricity at 5 V (15 W) or 15 V (45 W) to external devices.The USB Type-C charging ports are for charging only. They are not designed for data transfer or other purposes.Depending on the external device, it may not charge properly. Refer to the manual included with the device before using a USB charging port. Using the USB Type-C charging ports Front Rear (15 W if equipped) Note: The USB Type-C charging ports can be used when The power switch is in ACC or ON, or the multimedia system is on. Situations in which the USB Type-C charging ports may not operate correctly If a device which consumes more than 3 A at 5 V (15 W) or 15 V (45 W) is connected If a device designed to communicate with a personal computer, such as a USB memory device, is connected If the connected external device is turned off (depending on device) If the temperature inside the vehicle is high, such as after the vehicle has been parked in the sun About connected external devices Depending on the connected external device, charging may occasionally be suspended and then start again. This is not a malfunction. Notice: To prevent damage to the USB Type-C charging ports Do not insert foreign objects into the ports. Do not spill water or other liquids into the ports. When the USB Type-C charging ports are not in use, close the lids. If a foreign object or liquid enters a port may cause a short circuit. Do not apply excessive force to or impact the USB Type-C charging ports. Do not disassemble or modify the USB Type-C charging ports. To prevent damage to external devices Do not leave external devices in the vehicle. The temperature inside the vehicle may become high, resulting in damage to an external device. Do not push down on or apply unnecessary force to an external device or the cable of an external device while it is connected. To prevent 12-volt battery discharge Do not use the USB Type-C charging ports for a long period of time when the hybrid system is off. Wireless chargerWireless charger (if equipped) A portable device can be charged by just placing Qi standard wireless charge compatible portable devices according to the Wireless Power Consortium, such as smartphones and mobile batteries, etc., on the charge area. This function cannot be used with portable devices that are larger than the charging tray. Also, depending on the portable device, it may not operate as normal. Please read the operation manual for portable devices to be used. The “ Qi” logo The “ Qi” logo is a trademark of the Wireless Power Consortium. “ Qi” ID: 14561 Switches Wireless charger switch Name for all parts The illustration is for 2 portable devices. It may be only 1 unit depending on the specific design. Operation indicator light Charge area^* Charging tray Approximately 3.2 in. (82 mm) Approximately 5.9 in. (150 mm) ^*Portable devices and wireless chargers contain charging coils. The charging coil in the wireless charger can be moved within the charge area near the center of the charging tray. If the charging coil inside a portable device is detected in the charge area, the charging coil inside the wireless charger will move toward it and start charging. If the charging coil inside a portable device moves outside of the charge area, charging will automatically stop. If 2 or more portable devices are placed on the charging tray, their charging coils may not be properly detected and they may not be charged. Using the wireless charger Place the portable device on the charging tray Place the charging side of the portable device down with the center of the device in the center of the charge area. Depending on the portable device, its charging coil may not be in the center of the device. In this case, place the portable device so that its charging coil is centered in the charging area. When charging, the operation indicator light (orange) comes on. If charging is not occurring, try placing the portable device as close to the center of the charging area as possible. If charging is not performed, the operation indicator light will slowly illuminate in green and orange alternatively and a sound of charging coil operation may be heard repeatedly. When charging is complete, the operation indicator light (green) comes on. The illustration is for 2 portable devices. It may be only 1 unit depending on the specific design. Recharging function When charging is complete and after a fixed time in the charge suspension state, charging restarts. Rapid charging function The following portable devices support rapid charging. Portable devices compliant with WPC Ver1.3.3 and compatible with rapid charging iPhone’s with an iOS version that supports 7.5 W charging (iPhone 8 and later models) Portable devices compatible with Galaxy original rapid charging standard When a portable device that supports rapid charging is charged, charging automatically switches to the rapid charging function. Lighting conditions of operation indicator light

Operation indicator light	Conditions
Turning off	The power switch is off
Green (comes on)	On Standby (unable to charge state)*1
	On Standby (charging possible state)*2
	When charging is complete*3
Orange (comes on)	Charging
Orange flashes twice and then comes on	Charging frequency switching

^*1The condition for the smart key system to detect the key is established. ^*2Charging power will not be output during standby. A metallic object will not be heated, if it is placed on the wireless charger in this state. ^*3Depending on the portable device, there are cases where the operation indicator light will continue being lit up orange even after the charging is complete. When the wireless charger does not operate properly When the wireless charger does not operate properly, handle the probable cause based on the following tables.

Operation indicator light	Suspected causes/Handling method
Orange (Flashing repeatedly once every second)	Vehicle to wireless charger communication failure If the hybrid system is operating, stop and then restart the hybrid system. If the power switch is in ACC, start the hybrid system. (Starting the hybrid system)
Green (Flashing repeatedly once every second)	Dual wireless charger system communication failure If the hybrid system is operating, stop and then restart the hybrid system. If the power switch is in ACC, start the hybrid system. (Starting the hybrid system)
Green (comes on)	The smart key system is detecting the electronic key. Wait until electronic key detection has completed.
	Foreign substance detection: (1) There was a metal foreign object in the charging area before charging, and the foreign object detection function worked. Remove any foreign objects that are in the charging area. (2) Charging stopped when wearing a case with a Qi2 or MagSafe metal ring Remove the case.
Green (comes on)	Portable device misaligned / distanced from charging surface: The center of charging coil in the portable device moved outside of the charging area, or lens convex is large, or case is thick so the abnormal heating prevention function operated Remove the portable device from the wireless charger, after 5 seconds, then place the portable device so that it is near the center of the wireless charger. Also, if a case or cover is installed to the portable device, remove it.
	Battery protection function of portable device: Before full charging, battery protection function of portable device operated Confirm the setting of portable device.
	Continued detection of an electronic key: When a Multimedia function is used through vehicle customization, the electronic key is continually detected without being confirmed. In this case, turn the power switch ACC or ON to confirm the key.
	Moving mechanism Anomalies: The coil stopped working due to an abnormality in the moving mechanism If you do not hear the coil operating noise even after replacing it Consult your dealer.
Green (comes on)	Not Qi device: Green indicator not change, When put the device on tray. Please check the WPC website to see if your device supports Qi’s BPP or EPP
Orange (Repeatedly flashes 4 times continuously)	Safety shutdown resulting when the temperature within the wireless charger exceeded the set value Stop charging, remove the portable device from the wireless charger, wait for the temperature to drop, and then start charging again.

Note: The wireless charger can be operated when The power switch is in ACC or ON. Usable portable devices Qi standard wireless charge standard (with out MPP of Qi2) can be used on compatible devices. However, compatibility with portable devices that comply with Qi Ver. 1.0, 2.0.0 and later versions is not guaranteed. Starting with mobile phones and smartphones, it is aimed for low power electrically supplied portable devices of no more than 5W. However, charging exceeding 5 W is supported by the following portable devices. Charging at 7.5 W or less is supported by iPhone’s that support 7.5 W charging. Charging at 10 W or less is supported by Galaxy device that support 10 W charging of original standard. Charging at 15 W or less is supported by portable devices compliant with EPP output as defined by WPC standard Ver1.3.3. Using the smart key system If the smart key system detects the key while a device is being charged, charging will be temporarily stopped. AM receive synchronize functions When charging while listening to AM broadcasts, if noise occurs, perform manual switching as follows: Remove the device from the tray while it is charging. Confirm that the indicator has changed to a green light and the noise has stopped. Return the device that was taken off the tray and check if the indicator blinks orange twice and then lights up. If indicator blinks twice and the noise stops, the frequency switch is complete. If the indicator does not blink twice, lights up orange, and there is noise, repeat the process from step 1 and confirm that it blinks twice. Important points of the wireless charger When charging, the wireless charging device and portable device will get warmer, however this is not a malfunction.When a portable device gets warm while charging, charging may stop due to the protection function on the portable device side. In this case, when the temperature of the portable device drops significantly, charge again. The fan may start operating to lower the temperature inside the wireless charger, however this is not a malfunction. Operation sounds A buzzing noise may be heard when pressing the power supply switch to turn the power supply on, when turning the power switch to ACC or ON while the wireless charger power supply is on, or when detecting a portable device. However, this is not a malfunction. Cleaning the wireless charger Cleaning and protecting the vehicle interior Situations in which the function may not operate normally Devices may not be charged normally in the following situations. The portable device is fully charged The portable device is being charged with a cable connected There is foreign matter between the charge area and portable device Charging has caused the portable device to heat up The temperature around the charging tray is 95°F (35°C) or higher, such as in extreme heat The portable device is placed with its charging side facing up The small portable device such as foldable type is placed in an area misaligned from the charge area The portable device is larger than the charging tray The camera lens protrudes 3 mm (0.12 in) or more from the surface of the portable device(e.g.iPhone13 pro, iPhone13 pro Max) The vehicle is in an area where strong electrical waves or noise are emitted, such as near a television tower, power plant, gasoline station, broadcasting station, large display, airport, etc. When the any of the following objects are between the charging surface of a portable device and the charging area: Thick cases or covers Thick decorations Accessories, such as finger rings, straps, etc. A case or cover with convex shape around the camera lens Cover to protect the lens surface Non-slip mat When the portable device is in contact with, or is covered by any of the following metallic objects: A card that has metal on it, such as aluminum foil, etc. A pack of cigarettes that includes aluminum foil A wallet or bag that is made of metal Coins A heating pad CDs, DVDs or other media An accessory made of metal (Magsafe ring of metal) A case or cover made of metal (Magsafe ring of metal) Casing which has magnet in it on the charging side of the portable device Electric wave type wireless remote controls are being used nearby 2 or more portable devices are placed on the charging tray at the same time In case of using device built in S-pen (Galaxy “ Note” series etc.), device that inserted S-pen is placed on the tray If charging is abnormal or the operation indicator light continues to flash for any other reason, the wireless charger may be malfunctioning. Contact your Toyota dealer. If the smartphone OS has been updated If the smartphone OS has been updated to a newer version, its charging specifications may have changed significantly. For details, check the information on the manufacturer’s website. Trademark information iPhone is a trademark of Apple Inc., registered in the U.S. and other countries.MagSafe is a trademark or registered trademark of Apple Inc.. “ Galaxy” is a trademark or registered trademark of Samsung Electronics Co., Ltd. Warning: Caution while driving When charging a portable device, for safety reasons, the driver should not operate the main part of the portable device while driving. Caution while in motion Do not charge lightweight devices such as wireless headphones while in motion. These devices are very light and may be ejected from the charging tray, which may lead to unforeseen accidents. Caution regarding interference with electronic devices People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverters, as well as any other electrical medical device, should consult their physician about the usage of the wireless charger. To prevent malfunctions or burns Observe the following precautions. Failure to do so may result in a equipment failure and damage, catch fire, burns due to overheat or electric shock. Do not insert any metallic objects between the charge area and the portable device while charging Do not attach an aluminum sticker or other metallic object to the charge area Do not attach an aluminum sticker or other metallic object to the side of the portable device (or to its case or cover) that touches the charge area. Please refrain from using the retrofit metal ring and cases with products other than genuine MagSafe/Qi2 products, as there is a risk of heat generation. Do not use the charging tray as a small storage space Do not subject to a strong force or impact Do not disassemble, modify or remove Do not charge devices other than specified portable devices Keep away from magnetic items Do not charge devices if the charge area is covered in dust Do not cover with a cloth or similar material Notice: To prevent malfunctions and data corruptions When charging, bringing a credit, or other magnetic card, or magnetic storage media close to the charge area may clear any stored data due to magnetic influence. Also, do not bring a wristwatch or other precision instrument close to the charge area since doing so may cause it to malfunction. Do not charge with a non-contact IC card such as a transportation system IC card inserted between the charging side of a portable device and the charge area. The IC chip may become extremely hot and damage the portable device or IC card. Be especially careful not to charge a portable device inside a case or cover with a non-contact IC card attached. Do not leave portable devices inside the vehicle. The inside of the vehicle can become hot in extreme heat, which could cause a malfunction. To prevent 12-volt battery discharge Do not use the wireless charger for a long period of time when the hybrid system is stopped. ArmrestArmrest Fold down the armrest for use. Notice: To prevent damage to the armrest Do not apply too much load on the armrest. Assist gripsAssist grips An assist grip installed on the ceiling can be used to support your body while sitting on the seat. Warning: Assist grips Do not use the assist grip when getting in or out of the vehicle or rising from your seat. Notice: To prevent damage to the assist grip Do not hang any heavy object or put a heavy load on the assist grip. Hooks Coat hooks Coat hooksCoat hooks The coat hooks are provided with the rear assist grips. Warning: Items that must not be hanged on the hook Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.