Light bulbs You may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. Preparing for light bulb replacement Check the wattage of the light bulb to be replaced. (Light bulbs) Bulb location Front (type A) Front turn signal/parking lights Front side marker lights Front (type B) Front turn signal lights Front side marker lights Front (type C) Front turn signal lights Front side marker lights Rear Rear turn signal lights Back-up lights Lights that need to be replaced by your Toyota dealer Headlights Front turn signal lights (LED type) Daytime running lights Parking lights (LED type) Front side marker lights (LED type) Fog lights (if equipped) Side turn signal lights (if equipped) Tail lights Stop lights Rear side marker lights High mounted stoplight License plate lights Outer foot lights (if equipped) Note: LED lights The lights other than the following lights each consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. Front turn signal lights (bulb type) Parking lights (type A) Front side marker lights (bulb type) Rear turn signal lights Back-up lights Outer foot lights (if equipped) Condensation build-up on the inside of the lens Temporary condensation build-up on the inside of the light lens does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations: Large drops of water have built up on the inside of the lens. Water has built up inside the light. Replacing light bulb Front turn signal/parking lights (type A) Turn the bulb base counterclockwise. Remove the light bulb. Install a new light bulb then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. Front turn signal lights (type B and C) Turn the bulb base counterclockwise. Remove the light bulb. Install a new light bulb then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. Front side marker lights (type A) Turn the bulb base counterclockwise. Remove the light bulb. Install a new light bulb then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. Front side marker lights (type B and C) Turn the bulb base counterclockwise. Remove the light bulb. Install a new light bulb then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. Rear turn signal lights Open the back door and remove the cover. Remove the screws and remove the unit. Remove the lamp assembly by pulling it directly backward from the rear of the vehicle. Turn the bulb base counterclockwise. Remove the light bulb. Install a new light bulb then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. Align the grooves on the light unit with the claws, and insert the light unit straight so that the pin on the light unit fit into the hole. Confirm that the light unit is completely secured. Reinstall the screws. Reinstall the cover. Back-up lights Open the back door and remove the cover. To prevent damage to the cover, protect the tip of the screwdriver with a rag. Turn the bulb base counterclockwise. Remove the cord from the clip before turning the bulb base. Remove the light bulb. Install a new light bulb. Install the bulb base to the light unit by inserting it and turning the bulb base clockwise. Secure the cord with the clip back again after installing the bulb base. Reinstall the cover. Warning: Replacing light bulb Turn off the light. Do not attempt to replace the bulb immediately after turning off the light. The bulb become very hot and may cause burns. Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb. Also, if the bulb is scratched or dropped, it may blow out or crack. Fully install light bulb and any parts used to secure it. Failure to do so may result in heat damage, fire, or water entering the light unit. This may damage the light or cause condensation to build up on the lens. Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or component parts.Doing so may result in death or serious injury due to electric shock. To prevent damage or fire Make sure bulb is fully seated and locked. Check the wattage of the bulb before installing to prevent heat damage.