Digital Rear-view Mirror* * If equipped The Digital Rear-view Mirror is a system that uses the camera on the rear of the vehicle and displays its image on the display of the Digital Rear-view Mirror. The Digital Rear-view Mirror can be changed between optical mirror mode and digital mirror mode by operating the lever. The Digital Rear-view Mirror allows the driver to see the rear view despite obstructions, such as the head restraints or luggage, ensuring rear visibility. Also, the rear seats are not displayed and privacy of the passengers is enhanced. Warning: Observe the following precautions.Failure to do so may result in death or serious injury. Before using the Digital Rear-view Mirror Make sure to adjust the mirror before driving. (Adjusting the mirror) Change to optical mirror mode and adjust the position of the Digital Rear-view Mirror so that the area behind your vehicle can be viewed properly. Change to digital mirror mode and adjust the display settings. As the range of the image displayed by the Digital Rear-view Mirror is different from that of the optical mirror, make sure to check this difference before driving. System components Camera indicator Indicates that the camera is operating normally. Icon display area Displays icons, etc. (Display settings (digital mirror mode)) Menu/enter button Press to display the icons or select an item. Select button Press to move the cursor or adjust the image. Lever Operate to change between digital mirror mode and optical mirror mode. Changing modes Operate the lever to change between digital mirror mode and optical mirror mode. Digital mirror mode Displays an image of the area behind the vehicle. will illuminate in this mode. Optical mirror mode Turns off the display of the Digital Rear-view Mirror allows it to be used as an optical mirror. Note: Digital mirror mode operating condition The engine switch is turned to ON. When the engine switch is changed from ON to OFF or ACC, the image will disappear after several seconds. When using the Digital Rear-view Mirror in digital mirror mode If it is difficult to see the displayed image due to light reflected off the Digital Rear-view Mirror, the camera being dirty, or if lights of a vehicle behind your vehicle or the displayed image are bothering you, change to optical mirror mode. When the back door is open, the Digital Rear-view Mirror image may not display properly. Before driving, make sure the back door is closed. If the display is difficult to see due to reflected light, close the sunshade for the moon roof (if equipped) or the electronic sunshade for the panoramic moon roof (if equipped). Any of the following conditions may occur when driving in the dark, such as at night. None of them indicates that a malfunction has occurred. Colors of objects in the displayed image may differ from their actual color. Depending on the height of the lights of the vehicle behind, the area around the vehicle may appear white and blurry. Automatic image adjustment for brighter surrounding image may cause flickering. If it is difficult to see the displayed image or flickering bothers you, change to optical mirror mode. The Digital Rear-view Mirror may become hot while it is in digital mirror mode.This is not a malfunction. Depending on your physical condition or age, it may take longer than usual to focus on the displayed image. In this case, change to optical mirror mode. Do not let passengers stare at the displayed image when the vehicle is being driven, as doing so may cause motion sickness. Adjusting the mirror Adjusting the mirror height The height of the rear view mirror can be adjusted to suit your driving posture. Change to optical mirror mode, adjusting the height of the rear view mirror by moving it up and down. Display settings (digital mirror mode) Settings of the display in the digital mirror mode, on/off operation of the automatic anti-glare function, etc. can be changed. Press the menu/enter button. The icons will be displayed. Press / of the select buttons to select the desired icon, and press the menu/enter button. Press / of the select buttons to change the setting, and press the menu/enter button. When enabling/disabling or , press / of the select buttons to select (on) or (off), and press the menu/enter button. Press / of the select buttons to select , and press the menu/enter button. The icons will disappear.
Icons Settings
Select to enable/disable the automatic anti-glare function.* Responding to the brightness of the headlights of vehicles behind, the reflected light is automatically adjusted. The automatic anti-glare function is enabled each time the engine switch is changed to ON.
Select to adjust the brightness of the display.
Select to adjust the area displayed up/down.
Select to adjust the area displayed to the left/right.
Select to adjust the angle of the displayed image.
Select to zoom in/out the displayed image.
Select to enable/disable the PLS (point light source) mode. The glare from the headlights of vehicles behind is reduced to help ensure an image on the display in the digital mirror mode. When the PLS mode is enabled, will be displayed on the top left corner of the display.
*This is a function for the optical mirror mode, however, the setting can also be changed while using the digital mirror mode. Enabling/disabling the automatic anti-glare function (optical mirror mode) The automatic anti-glare function in the optical mirror mode can be enabled/disabled. The setting can be changed in both the digital mirror mode and the optical mirror mode. When using the digital mirror mode Display settings (digital mirror mode) When using the optical mirror mode Press the menu/enter button. The setting display will be displayed. Press / of the select buttons to select (on) or (off), and press the menu/enter button. The icons will disappear. Note: Adjusting the display (digital mirror mode) The icons will disappear if a button is not operated for approximately 10 seconds or more. If the displayed image is adjusted, it may appear distorted. This is not a malfunction. If the brightness of the Digital Rear-view Mirror is set too high, it may cause eye strain. Adjust the Digital Rear-view Mirror to an appropriate brightness. If your eyes become tired, change to optical mirror mode. The brightness of the Digital Rear-view Mirror will change automatically according to the brightness of the area in front of your vehicle. Sensor Digital Rear-view Mirror To prevent the light sensors from malfunctioning To prevent the light sensors from malfunctioning, do not touch or cover them. Warning: Observe the following precautions.Failure to do so may result in death or serious injury. While driving Do not adjust the position of the Digital Rear-view Mirror or adjust the display settings while driving.Stop the vehicle and operate the Digital Rear-view Mirror control switches. Failure to do so may cause a steering wheel operation error, resulting in an unexpected accident. Always pay attention to the vehicle’s surroundings. The size of the vehicles and other objects may look different when in digital mirror mode and optical mirror mode.When backing up, make sure to directly check the safety of the area around your vehicle, especially behind the vehicle.Additionally, if a vehicle approaches from the rear in the dark, such as at night, the surrounding area may appear dim. Cleaning the Digital Rear-view Mirror Cleaning the mirror surface If the mirror surface is dirty, the image on the display may be difficult to see.Clean the mirror surface gently using a soft dry cloth. Cleaning the camera If the camera lens is dirty, the displayed image may not be clear. In this case, clean it with a soft cloth dampened with water. Note: The camera The camera for the Digital Rear-view Mirror is located as shown. Notice: To prevent the Digital Rear-view Mirror from malfunctioning Do not remove, disassemble or modify the mirror. To prevent the camera from malfunctioning Observe the following precautions, otherwise the Digital Rear-view Mirror may not operate properly. Do not strike or hit the camera or subject it to a strong impact, as the camera installation position and angle may be changed. Do not remove, disassemble or modify the camera. When cleaning the camera lens, wipe the camera lens with a damp soft cloth.Do not strongly rub the camera lens, as it may be scratched and will not be able to transmit a clear image. When applying colored film (including transparent film) to the rear window glass, do not apply it to the area in front of the camera.If film is applied to the area in front of the camera, the image from the camera may not display properly. Do not subject the camera to a strong impact as this could cause a malfunction.If this happens, have the vehicle inspected by your Toyota dealer as soon as possible. If you notice any symptoms If you notice any of the following symptoms, refer to the following table for the likely cause and the solution. If the symptom is not resolved by the solution, have the vehicle inspected by your Toyota dealer.
Symptom Likely cause Solution
The image is difficult to see. The mirror surface is dirty. Clean the mirror surface gently, using a soft dry cloth.
Sunlight or headlights are shining directly into the Digital Rear-view Mirror. Change to optical mirror mode.(If the light is coming through the moon roof [if equipped] or panoramic moon roof [if equipped], close the sunshade or electronic sunshade.)
The vehicle is in a dark area. The vehicle is near a TV tower, broadcasting station, electric power plant, or other location where strong radio waves or electrical noise may be present. The temperature around the camera is extremely high/low. The ambient temperature is extremely low. It is raining or humid. Sunlight or headlights are shining directly into the camera lens. The vehicle is under fluorescent lights, sodium lights, mercury lights, etc. Exhaust gas is obstructing the camera. Change to optical mirror mode.(Change back to digital mirror mode when the conditions have improved.)
The image is difficult to see. The rear window glass is fogged up. Change to optical mirror mode.After defogging the rear window using the rear window defogger (Air conditioning controls - Defogging the rear window and outside rear view mirrors (if equipped), Air conditioning controls - Defogging the rear window and outside rear view mirrors (if equipped)), use the digital mirror mode again.
The outside of the rear window glass is dirty. Use the rear window wiper to remove dirt.
The inside of the rear window glass is dirty. Wipe the inside of rear window glass with a damp soft cloth.
The image is out of alignment. The back door is not fully closed. Fully close the back door.
The camera or its surrounding area has received a strong impact. Change to optical mirror mode and have the vehicle inspected by your Toyota dealer.
The display is dim and is displayed. The system may be malfunctioning. Change to optical mirror mode and have the vehicle inspected by your Toyota dealer.
goes off.
is displayed. The Digital Rear-view Mirror is extremely hot.(The display will gradually become more dim. If the temperature continues to increase, the Digital Rear-view Mirror will turn off.) Reducing the cabin temperature is recommended to reduce the temperature of the mirror.( will disappear when the mirror becomes cool.) If does not disappear even though the mirror is cool, have the vehicle inspected by your Toyota dealer.
The lever cannot be operated properly. The lever may be malfunctioning. Change to optical mirror mode and have the vehicle inspected by your Toyota dealer.(To change to optical mirror mode, press and hold the menu/enter button for approximately 10 seconds.)