Light bulbs You may replace the following bulbs by yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. Preparing for light bulb replacement Check the wattage of the light bulb to be replaced. (Light bulbs) Turning off the power back door main switch Power back door Bulb locations Front (type A) Front turn signal lights/parking lights Front side marker lights Front (type B) Front turn signal lights Front side marker lights Front (type C) Front turn signal lights/parking lights Front side marker lights Rear Rear turn signal lights Back-up lights License plate lights Lights that need to be replaced by your Toyota dealer Headlight low beams Headlight high beams Daytime running lights (types A and C) Daytime running lights/parking lights (type B) Front fog lights Side turn signal lights Tail lights/stop lights Rear side marker lights Tail lights High mounted stoplight Outer foot lights (if equipped) Note: LED lights The lights other than the following lights each consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. Front turn signal lights/parking lights (types A and C) Front turn signal lights (type B) Front side marker lights Rear turn signal lights Back-up lights License plate lights Condensation build-up on the inside of the lens Temporary condensation build-up on the inside of the light lens does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations: Large drops of water have built up on the inside of the lens. Water has built up inside the light. When replacing light bulbs When replacing light bulbs Replacing light bulbs Front turn signal lights/parking lights (types A and C) and front turn signal lights (type B) Turn the bulb base counterclockwise and remove it. Remove the light bulb. Install a new light bulb, and then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. After installing the bulb base, wiggle it lightly to make sure it is securely installed and turn the lights and turn signal lights on to visually check that there is no light leaking from between the bulb base and light unit. Front side marker lights Turn the bulb base counterclockwise and remove it. Remove the light bulb. Install a new light bulb, and then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. After installing the bulb base, wiggle it lightly to make sure it is securely installed and turn the lights on to visually check that there is no light leaking from between the bulb base and light unit. Rear turn signal lights Open the back door and using a flathead screwdriver, remove the cover. To prevent damage to the vehicle, wrap the tip of the flathead screwdriver with tape, etc. Remove the securing 2 screws and light unit. Remove the light unit by pulling it straight back from the rear of the vehicle. Disconnect the wire harness. Turn the bulb base counterclockwise and remove it. Remove the light bulb. Install a new light bulb, and then install the bulb base to the light unit by inserting it and turning it clockwise. After installing the bulb base, wiggle it lightly to make sure it is securely installed and turn on the turn signal lights to visually check that there is no light leaking from between the bulb base and light unit. Install the light unit. Align the 2 guides and push the light unit toward the front of the vehicle to install it. Install the 2 screws. Install the cover. Back-up lights Open the back door and remove the cover. Using a flathead screwdriver, remove the cover. To prevent damage to the vehicle, wrap the tip of the flathead screwdriver with tape, etc. Turn the bulb base counterclockwise and remove it. Remove the light bulb. Install a new light bulb, and then install the bulb base to the light unit by inserting it and turning it clockwise. After installing the bulb base, wiggle it lightly to make sure it is securely installed and turn on the back-up lights to visually check that there is no light leaking from between the bulb base and light unit. Install the cover. Align the tabs of the cover with the grooves and install the cover. License plate lights Remove the cover. Using a flathead screwdriver, remove the cover. To prevent damage to the vehicle, wrap the tip of the flathead screwdriver with tape, etc. Remove the lens. Lens Hook Insert a small flathead screwdriver, etc. into either the right or left hole of the lens. Push the screwdriver sideways in the direction of the arrow shown in the illustration, disengage the hook, and then remove the lens. To prevent damage to the vehicle, wrap the tip of the screwdriver with tape, etc. Remove the light bulb. Install a new light bulb. Install the lens. Hooks Fit the lens into either the right or left hooks. Push the lens into place. After installation, confirm that the lens is properly installed by gently pulling it. Install the cover. Warning: To prevent injury Before performing any light bulb replacement procedure, be sure to turn the power switch off. Failure to do so may result in burns from hot components or a part of your body may get caught on an operating component, possibly causing serious injury. Replacing light bulbs Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights.The bulbs become very hot and may cause burns. Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb. Also, if the bulb is scratched or dropped, it may blow out or crack. Fully install light bulbs and any parts used to secure them. Failure to do so may result in heat damage, fire, or water entering the light unit. This may damage the lights or cause condensation to build up on the lens. Do not attempt to repair or disassemble light bulbs, connectors, electric circuits or component parts.Doing so may result in death or serious injury due to electric shock. To prevent damage or fire Make sure bulbs are fully seated and locked. Check the wattage of the bulb before installing to prevent heat damage.