Gauges and meters Meter display Engine coolant temperature gauge Outside temperature Engine Tachometer Tachometer Speedometer Meter Clock Clock Fuel Fuel gauge Fuel gaugeLocations of gauges and meters 4.2-inch display 7-inch display The units used on the meters may differ depending on the target region. Hybrid System Indicator Displays hybrid system output or regeneration level (Hybrid System Indicator) Multi-information display Presents the driver with a variety of vehicle data (Multi-information display (4.2-inch display), Multi-information display (7-inch display)) Displays warning messages in case of a malfunction (If a warning message is displayed) Clock (Adjusting the clock) Speedometer Fuel gauge Displays the quantity of fuel remaining in the tank Odometer and trip meter display (Odometer and trip meter display) Shift position display (Hybrid transmission) Outside temperature Displays the outside temperature within the range of -40°F (-40°C) to 122°F (50°C). Low outside temperature indicator comes on when the ambient temperature is 37°F (3°C) or lower. Engine coolant temperature gauge Displays the engine coolant temperature Note: The meters and display illuminate when The power switch is in ON. Meter Hybrid System Indicator Hybrid System IndicatorHybrid System Indicator READY OFF area Shows that the hybrid system is not operating. Charge area Shows regeneration^* status. Regenerated energy will be used to charge the hybrid battery (traction battery). Hybrid Eco area Shows that gasoline engine power is not being used very often. The gasoline engine will automatically stop and restart under various conditions. Eco area Shows that the vehicle is being driven in an Eco-friendly manner. By keeping the indicator needle within the Eco area, more Eco-friendly driving can be achieved. Power area Shows that an Eco-friendly driving range is being exceeded (during full power driving etc.) ^*When used in this manual, regeneration refers to the conversion of energy created by the movement of the vehicle into electrical energy. Outside temperature display In the following situations, the correct outside temperature may not be displayed, or the display may take longer than normal to change: When stopped, or driving at low speeds (less than 12 mph [20 km/h]) When the outside temperature has changed suddenly (at the entrance/exit of a garage, tunnel, etc.) When “ --” or “ E” is displayed, the system may be malfunctioning. Take your vehicle to your Toyota dealer. Liquid crystal display Small spots or light spots may appear on the display. This phenomenon is characteristic of liquid crystal displays, and there is no problem continuing to use the display. Customization The meters can be customized on of the multi-information display. (Settings display - Meter settings, Settings display - Meter settings) Warning: The information display at low temperatures Allow the interior of the vehicle to warm up before using the liquid crystal information display. At extremely low temperatures, the information display monitor may respond slowly, and display changes may be delayed. For example, there is a lag between the driver’s shifting and the new gear number appearing on the display. This lag could cause the driver to downshift again, causing rapid and excessive engine braking and possibly an accident resulting in death or injury. Notice: To prevent damage to the engine and its components Do not let the indicator needle of the tachometer enter the red zone, which indicates the maximum engine speed. The engine may be overheating if the engine coolant temperature gauge is in the red zone (H). In this case, immediately stop the vehicle in a safe place, and check the engine after it has cooled completely. (If your vehicle overheats) Odometer Trip meters Distance until next engine oil changeOdometer and trip meter display Odometer and trip meter display Display items Display items Odometer Displays the total distance the vehicle has been driven. Trip meter A/trip meter B Displays the distance the vehicle has been driven since the meter was last reset. Trip meters A and B can be used to record and display different distances independently. Switches “ODO TRIP” switch “ODO TRIP” switch Odometer and trip meter display “ODO TRIP” switch Changing the display Each time the “ ODO TRIP” switch is pressed, the displayed item will be changed. When the trip meter is displayed, pressing and holding the switch will reset the trip meter. Switches Instrument panel light control switches Meter Instrument panel light control Instrument panel light control Brightness control Instrument panel light control Changing the instrument panel light brightness The brightness of the instrument panel lights can be adjusted. This image is for example only, and may differ from the actual vehicle. Darker Brighter Note: Brightness of the meters (day mode and night mode) The brightness of the meters is changed between day mode and night mode. Day mode: When the surrounding area is bright Night mode: When the surrounding area is dark Meter Clock ClockAdjusting the clock The clocks can be adjusted on the audio system screen. Refer to “ NAVIGATION AND MULTIMEDIA SYSTEM OWNER’S MANUAL”.