Multi-terrain Select (AWD models) Multi-terrain Select is a system that improves drivability in off-road situations. When driving over muddy, sandy or rough road surfaces, the system selects a suitable driving mode to switch AWD, brake and drive force control to perform control suitable for the road condition. Warning: Before using Multi-terrain Select Make sure to observe the following precautions. Failure to observe these precautions may result in an unexpected accident. Check that the Mud & Sand and Rock & Dirt indicators are illuminated before driving. Multi-terrain Select will not operate when the indicators are off. Do not rely solely upon the Multi-terrain Select. This function is not intended to expand the limits of the vehicle. If the system is continuously used for a long period of time, the load on related parts increases and the system may be unable to operate normally, which may lead to an accident. Thoroughly check the road conditions and driving route before driving, and drive with caution. The road conditions listed (Guidelines for selecting each mode:Guidelines for selecting each mode) are for reference only. There is a chance that the function may not be the most appropriate in terms of road conditions such as pitch, slipperiness, undulation, etc. Thoroughly check the road conditions before driving. Guidelines for selecting each mode Control that is suitable for the following road conditions can be performed by switching to either of the two modes. Select a mode that is appropriate for the road condition. Mud & Sand mode Suitable for driving on roads with increased driving resistance such as sandy roads, muddy roads, etc. Rock & Dirt mode Suitable for driving in bumpy road conditions, such as on unpaved forest roads. Normal modeChanging the mode Dynamic Torque Control AWD vehicles Mud & Sand mode When the switch is pressed while not in Mud & Sand mode, the system switches to Mud & Sand mode and the Mud & Sand mode indicator, VSC OFF indicator and PCS warning light illuminate on the multi-information display. Normal mode Mode that performs AWD, brake and drive force control suitable for driving on general roads. Use normal mode when not driving off-road. The driving mode returns to normal mode if the switch is pressed while in Mud & Sand mode or Rock & Dirt mode. Rock & Dirt mode When the switch is pressed while not in Rock & Dirt mode, the system switches to Rock & Dirt mode and the Rock & Dirt mode indicator illuminates on the multi-information display. Dynamic Torque Vectoring AWD vehicles Mud & Sand mode When the switch is turned to the left while not in Mud & Sand mode, the system switches to Mud & Sand mode and the Mud & Sand mode indicator, VSC OFF indicator and PCS warning light illuminate on the multi-information display. Normal mode Mode that performs AWD, brake and drive force control suitable for driving on general roads. Use normal mode when not driving off-road. The driving mode returns to normal mode if the switch is pressed while in Mud & Sand mode or Rock & Dirt mode. Rock & Dirt mode When the switch is turned to the right while not in Rock & Dirt mode, the system switches to Rock & Dirt mode and the Rock & Dirt mode indicator illuminates on the multi-information display. Note: Multi-terrain Select Multi-terrain Select is intended for use when driving on rough roads. Drive in normal mode during normal driving. The Mud & Sand and Rock & Dirt modes control the vehicle so that it can maximize the drive force and improve drivability on rough roads. As a result, fuel efficiency may diminish when compared to driving in normal mode. If Mud & Sand or Rock & Dirt mode is selected The AWD operation status display will automatically switch on the multi-information display. AWD control for Mud & Sand and Rock & Dirt modes If the vehicle speed exceeds the speeds listed below, the same level of AWD control for Normal mode is performed, even if Mud & Sand or Rock & Dirt mode is selected. Mud & Sand mode: Vehicle speed is approximately 25 mph (40 km/h) or more Rock & Dirt mode: Vehicle speed is approximately 16 mph (25 km/h) or more If the vehicle speed drops below the above speeds, the system automatically returns to the AWD control for each mode. When Multi-terrain Select brake control temporarily stops operating If Mud & Sand or Rock & Dirt mode is continuously used for a long period of time, the brakes may overheat, and Multi-terrain Select brake control may temporarily stop operating. At this time, the buzzer sounds intermittently and “Traction Control Turned OFF” is displayed on the multi-information display. If Multi-terrain Select brake control stops operating, stop the vehicle in a safe location as soon as possible^* and wait until the system temperature decreases. Once the display message on the multi-information display turns off, the brake control returns to normal. Note that normal driving is still possible even when Multi-terrain Select brake control is not operating. ^*After stopping the vehicle, do not stop the engine until the display message has turned off. When Mud & Sand or Rock & Dirt mode is canceled In the following situations, Mud & Sand mode or Rock & Dirt mode are automatically canceled even if they are selected. When the driving mode is changed (Driving mode select switch) When the engine switch is turned off Driving in Mud & Sand or Rock & Dirt mode The following types of situations may occur, but they are not malfunctions. Vibrations may be felt throughout the vehicle or steering wheel Operating noise may be heard from the engine compartment When an inspection at your Toyota dealer is necessary In the following situations, the system may be malfunctioning. Have the vehicle inspected by your Toyota dealer immediately. When the slip indicator light illuminates while Mud & Sand or Rock & Dirt mode is selected When the indicator for each mode does not illuminate even though Mud & Sand or Rock & Dirt mode is selected