Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. Preparing for light bulb replacement Check the wattage of the light bulb to be replaced. (Light bulbs) Bulb locations Front Front turn signal/parking lights (bulb type) Rear Back-up lights (bulb type) Rear turn signal lights (bulb type) Bulbs that need to be replaced by your Toyota dealer Headlights Daytime running lights Parking lights (LED type) Front turn signal lights (LED type) Front side marker lights Accent lights (if equipped) Side turn signal lights (if equipped) Tail lights Stop lights Back-up lights (LED type) Rear turn signal lights (LED type) Rear side marker lights High mounted stoplight License plate lights Note: Headlights Replacing light bulbs Daytime running lights Replacing light bulbs Parking lights Replacing light bulbs Turn signal lights Replacing light bulbs Front turn signal lights Replacing light bulbs Side turn signal lights Replacing light bulbs Tail lights Replacing light bulbs Stop lights Replacing light bulbs Back-up lights Replacing light bulbs Rear turn signal lights Replacing light bulbs Rear side marker lights Replacing light bulbs Lights Replacing light bulbs High mounted stoplight Replacing light bulbs License plate lights Replacing light bulbs LED light bulbs The lights other than the front turn signal/parking lights (bulb type), back-up lights (bulb type) and rear turn signal lights (bulb type) consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. Condensation build-up on the inside of the lens Temporary condensation build-up on the inside of the lens of any lights does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations: Large drops of water have built up on the inside of the lens of any light. Water has built up inside of any lights. When replacing light bulbs When replacing light bulbs Replacing light bulbs Front turn signal/parking lights Replacing light bulbs Front turn signal/parking lights (bulb type) Turn the bulb base counterclockwise and remove it. Remove the light bulb. Install a new light bulb, and then install the bulb base to the light unit by inserting it and turning the bulb base clockwise. After installing the bulb base, wiggle it lightly to make sure it is securely installed and turn the lights and turn signal lights on to visually check that there is no light leaking from between the bulb base and light unit. Rear turn signal lights Replacing light bulbs Rear turn signal lights (bulb type) Open the trunk lid. Insert a flathead screwdriver between the cover and the light assembly and pry up the cover to disengage the claws (indicated by a dotted line). To prevent scratching the vehicle, wrap the tip of the flathead screwdriver with a cloth, etc. Pull the cover toward the rear of the vehicle and remove the cover. Remove the 2 screws and then remove the light assembly by pulling it straight back. Turn the bulb base counterclockwise. Remove the light bulb. When installing the light bulb, install it by conducting steps 6 and 5 with the directions reversed. Install the light assembly and then install the 2 screws. Align the guide and pin on the light assembly with the mounting when installing it. Install the cover. Back-up lights Replacing light bulbs Back-up lights (bulb type) Open the trunk lid, remove the clips, and pull back the cover. When removing a clip, use a flathead screwdriver to pry the center portion out and then remove the whole clip. Disconnect the connector while depressing the lock release. Turn the bulb base counterclockwise and remove it. Remove the light bulb. Install a new light bulb, install the bulb base to the light unit, turn the bulb base clockwise, and connect the connector. After installing the bulb base, wiggle it lightly to make sure it is securely installed and turn on the back-up lights to visually check that there is no light leaking from between the bulb base and light unit. Reinstall the trunk lid cover with the clips. Warning: To prevent injury Before performing any light bulb replacement procedure, be sure to turn the power switch off. Failure to do so may result in burns from hot components or a part of your body may get caught on an operating component, possibly causing serious injury. Replacing light bulbs Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights. The bulbs become very hot and may cause burns. Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb. Also, if the bulb is scratched or dropped, it may blow out or crack. Fully install light bulbs and any parts used to secure them. Failure to do so may result in heat damage, fire, or water entering the light unit. This may damage the lights or cause condensation to build up on the lens. Do not attempt to repair or disassemble the light bulbs, connectors, electric circuits or component parts.Doing so may result in death or serious injury due to electric shock. To prevent damage or fire Make sure bulbs are fully seated and locked. Check the wattage of the bulb before installing to prevent heat damage.