Other interior features

USB charging portsUSB charging ports

USB Type-A port: The USB charging port is used to supply 2.5 A of electricity at 5 V to external devices.

USB Type-C port: The USB charging ports are used to supply 3.0 A of electricity at 5 V to external devices.

The USB charging ports are for charging only. They are not designed for data transfer or other purposes.Depending on the external device, it may not charge properly. Refer to the manual included with the device before using a USB charging port.

Using the USB charging ports

On the instrument panel (USB Type-C port)

Rear of the console box

Open the lid.

USB Type-A port

USB Type-C port

Note:

The USB charging ports can be used when

The power switch is in ACC or ON.

Situations in which the USB charging ports may not operate correctly

USB Type-A port: If a device which consumes more than 2.5 A at 5 V is connected

USB Type-C port: If a device which consumes more than 3.0 A at 5 V is connected

If a device designed to communicate with a personal computer, such as a USB memory device, is connected

If the connected external device is turned off (depending on device)

If the temperature inside the vehicle is high, such as after the vehicle has been parked in the sun

About connected external device

Depending on the connected external device, charging may occasionally be suspended and then start again. This is not a malfunction.

Notice:

To prevent damage to the USB charging ports

Do not insert foreign objects into the ports.

Do not spill water or other liquids into the ports.

Do not apply excessive force to or impact the USB charging ports.

Do not disassemble or modify the USB charging ports.

To prevent damage to external devices

Do not leave external devices in the vehicle. The temperature inside the vehicle may become high, resulting in damage to an external device.

Do not push down on or apply unnecessary force to an external device or the cable of an external device while it is connected.

To prevent 12-volt battery discharge

Do not use the USB charging ports for a long period of time with the hybrid system stopped.

Wireless chargerWireless charger

A portable device, such as a smartphone or mobile battery, can be charged by just placing it on the charging area, provided the device is compatible with the Qi wireless charging standard created by the Wireless Power Consortium.

The compatible portable devices can be found on the following Wireless Power Consortium website.https://www.wirelesspowerconsortium.com/

The wireless charger cannot be used with a portable device that is larger than the charging tray. Additionally, depending on the portable device, the wireless charger may not operate properly. Refer to the operation manual of the portable device.

The “Qi” logo

The “Qi” logo is a trademark of the Wireless Power Consortium. Qi ID: 11277

Name for all parts

Operation indicator light

Charge area^*

Charging tray

Approximately 3.9 in. (10 cm)

Approximately 1.0 in. (2.5 cm)

Compatible portable devices and the wireless charger contain charging coils. The charging coil in the wireless charger can be moved within the charge area up to the position of the charging coil inside a portable device. Charging is possible if the center of the coil of the portable device is placed within the charge area.Additionally, if 2 or more portable devices are placed on the charging tray at the same time, each charging coil may not be detected correctly and charging may not be possible.

Using the wireless charger

Place the portable device on the charging area.

Place the charging side of the portable device down with the center of the device in the center of the charging area.

When charging, the operation indicator light (orange) comes on.

Refer to “Situations in which the function may not operate normally” when charging is not performed.(Situations in which the function may not operate normally)

When charging is complete, the operation indicator light (green) comes on.

Recharging function

When charging is complete and after a fixed time in the charge suspension state, charging restarts.

When a portable device is moved significantly in the charging area, the charging coil is disconnected and charging is stopped momentarily. However, if there is the center of a charging coil in the charging area, the charging coil inside the wireless charger will move toward it and then charging restarts.

Rapid charging function

The following portable devices support rapid charging.

Portable devices compliant with WPC Ver 1.3.2 and compatible with rapid charging

iPhone’s with an iOS version that supports 7.5 W charging (iPhone 8 and later models)

Portable devices compatible with Galaxy original rapid charging standard

When a portable device that supports rapid charging is charged, charging automatically switches to the rapid charging function.

Operation indicator light status


Operation indicator light		Conditions
Charging tray	Multimedia display	Conditions
Turning off	Disappear	When the Multimedia system power supply is off or the power switch is in OFF.
Green (comes on)	Gray	On Standby (charging possible state)^*1
Green (comes on)	Gray	When charging is complete^*2
Orange (comes on)	Blue	Charging

^*1

Charging power will not be output during standby. A metallic object will not be heated, if it is placed on the charging area in this state.

^*2

Depending on the portable device, there are cases where the operation indicator light will continue being lit up orange even after the charging is complete.

The wireless charger is not working properly

The following are situations in which the wireless charger does not work properly and how to deal with the possible causes.


Operation indicator light		Suspected causes/Handling method
Charging tray	Multimedia display	Suspected causes/Handling method
Orange (Flashing repeatedly once every second)	Gray	Vehicle to wireless charger communication failure If the hybrid system is operating, stop and then restart the hybrid system. If the power switch is in ACC, start the hybrid system. (Power (ignition) switch)
Green (Flashing repeatedly once every second)	Disappear	Wireless charger and multimedia system communication failure If the hybrid system is operating, stop and then restart the hybrid system. If the power switch is in ACC, start the hybrid system. (Power (ignition) switch)
Green (comes on)	Blue	AM radio stations are being automatically selected Wait until the system has completed the automatic selection of AM radio stations. In the case that automatic selection cannot be completed, stop automatic selection.
Green (comes on)	Blue	The smart key system is detecting the key. Wait until key detection has completed.
Green (comes on)	Gray	Foreign substance detection: A metallic foreign substance is in the charging area, and so the abnormal heating prevention function of the metallic foreign substance operated Remove the foreign substance from the charge area.
		Portable device misaligned / distanced from charging surface: The center of charging coil in the portable device moved outside of the charging area, or lens convex is large, or case is thick so the abnormal heating prevention function operated Remove the portable device from the wireless charger, after 5 seconds, then place the portable device so that it is near the center of the wireless charger. Also, if a case or cover is installed to the portable device, remove it.
		Battery protection function of portable device: Before full charging, battery protection function of portable device operated Confirm the setting of portable device.
		Continued detection of an electronic key: When a Multimedia function is used through vehicle customization, the electronic key is continually detected without being confirmed. In this case, turn the power switch ACC or ON to confirm the key.
Orange (Repeatedly flashes 4 times continuously)	Gray	Safety shutdown resulting when the temperature within the wireless charger exceeded the set value Stop charging, remove the portable device from the charging tray, wait for the temperature to drop, and then start charging again.

Note:

The wireless charger can be operated when

The power switch is in ACC or ON.

Portable devices that can be charged

Portable devices compatible with the Qi wireless charging standard can be charged by the wireless charger. However, compatibility with portable devices that comply with Qi Ver. 1.0, 1.3.2 and later versions is not guaranteed.

The wireless charger is designed to supply low power electricity (5 W or less) to a cellular phone, smartphone, or other portable device.

However, portable devices, such as the following, can be charged with more than 5 W.

7.5 W charging compatible iPhones can be charged at 7.5 W or less.

Devices that comply with independent Galaxy charging standards support 10 W or less charging. Check the specifications of each portable device for the charging electricity.

Portable devices compliant with EPP output as defined by WPC standard Ver1.3.2. can be charged at 15 W or less.

Using the smart key system

If the smart key system detects the key while a device is being charged, charging will be temporarily stopped.

When covers and accessories are attached to portable devices

Do not charge in situations where cover and accessories not able to handle Qi are attached to the portable device. Depending on the type of cover (including for certain genuine manufacturer parts) and accessory, it may not be possible to charge. When charging is not performed even with the portable device placed on the charge area, remove the cover and accessories.

AM radio cooperation function during charging

During charging, if noise occurs when listening to the AM radio, the charging frequency is automatically changed to reduce the noise.

When automatically seeking AM radio stations, charging will be suspended to prevent charging noise from being detected as a radio station. Charging will resume automatically when seek tuning is stopped.

Important points of the wireless charger

If the electronic key cannot be detected within the vehicle interior, charging cannot be done. When the door is opened and closed, charging may be temporarily suspended.

When charging, the wireless charging device and portable device will get warmer, however this is not a malfunction. When a portable device gets warm while charging, charging may stop due to the protection function on the portable device side. In this case, when the temperature of the portable device drops significantly, charge again.

The fan may start operating to lower the temperature inside the wireless charger, however this is not a malfunction.

Operation sounds

A buzzing noise may be heard when pressing the power switch to turn to ACC or ON or when detecting a portable device. However, this is not a malfunction.

Cleaning the wireless charger

Cleaning and protecting the vehicle interior

Situations in which the function may not operate normally

Devices may not be charged normally in the following situations.

The portable device is fully charged

The portable device is being charged with a cable connected

There is foreign matter between the charge area and portable device

Charging has caused the portable device to heat up

The temperature around the charging tray is 95°F (35°C) or higher, such as in extreme heat

The portable device is placed with its charging side facing up

The small portable device such as foldable type is placed in an area misaligned from the charge area

The portable device is larger than the charging tray

The camera lens protrudes 0.12 in. (3 mm) or more from the surface of the portable deviceEx) iPhone13 pro, iPhone13 pro Max

The vehicle is in an area where strong electrical waves or noise are emitted, such as near a television tower, power plant, gasoline station, broadcasting station, large display, airport, etc.

When the any of the following objects are between the charging surface of a portable device and the charging are:

Thick cases or covers

Thick decorations

Accessories, such as finger rings, straps, etc.

A case or cover with convex shape around the camera lens

When the portable device is in contact with, or is covered by any of the following metallic objects:

A card that has metal on it, such as aluminum foil, etc.

A pack of cigarettes that includes aluminum foil

A wallet or bag that is made of metal

Coins

A heating pad

CDs, DVDs or other media

A accessory made of metal

A case or cover made of metal

Casing which has magnet in it on the charging side of the portable device

Electric wave type wireless remote controls are being used nearby

The electronic key is not inside the vehicle

2 or more portable devices are placed on the charging tray at the same time

In case of using device built in S-pen (Galaxy “Note” series etc.), device that inserted S-pen is placed on the tray

In situations other than above, if the wireless charger does not operate properly, the wireless charger may be malfunctioning.

Contact your Toyota dealer.

If the smartphone OS has been updated

If the smartphone OS has been updated to a newer version, its charging specifications may have changed significantly. For details, check the information on the manufacturer’s website.

Trademark information

iPhone is a trademark of Apple Inc., registered in the U.S. and other countries.

Galaxy is a trademark or registered trademark of Samsung Electronics Co.,Ltd.

Warning:

Caution while driving

When charging a portable device, for safety reasons, the driver should not operate the main part of the portable device while driving.

Precautions for when driving

Do not charge small, lightweight portable devices, such as wireless earbuds, while driving. Lightweight devices may fly off of the charging tray, possibly leading to an accident.

Caution regarding interference with electronic devices

People with implantable cardiac pacemakers, cardiac resynchronization therapy-pacemakers or implantable cardioverters, as well as any other electrical medical device, should consult their physician about the usage of the wireless charger.

Operations of the wireless charger may have an affect on medical devices.

To prevent malfunctions or burns

Observe the following precautions.

Failure to do so may result in a equipment failure and damage, catch fire, burns due to overheat or electric shock.

Do not insert any metallic objects between the charge area and the portable device while charging.

Do not attach an aluminum sticker or other metallic object to the charge area.

Do not attach an aluminum sticker or other metallic object to the side of the portable device (or to its case or cover) that touches the charge area.

Do not use the charging tray as a small storage space.

Do not subject to a strong force or impact.

Do not disassemble, modify or remove.

Do not charge devices other than specified portable devices.

Keep away from magnetic items.

Do not charge devices if the charge area is covered in dust.

Do not cover with a cloth or similar material.

Notice:

To prevent trouble and data damage

When charging, bringing a credit, or other magnetic card, or magnetic storage media close to the charge area may clear any stored data due to magnetic influence. Also, do not bring a wristwatch or other precision instrument close to the charge area since doing so may cause it to malfunction.

Do not charge with a non-contact IC card such as a transportation system IC card inserted between the charging side of a portable device and the charge area. The IC chip may become extremely hot and damage the portable device or IC card. Be especially careful not to charge a portable device inside a case or cover with a noncontact IC card attached.

Do not leave portable devices inside the vehicle. The inside of the vehicle can become hot in extreme heat, which could cause a malfunction.

To prevent 12-volt battery discharge

Do not use the wireless charger for a long period of time when the hybrid system is stopped.

Power outletPower outlet

Please use as a power supply for electronic goods that use less than 12 VDC/10 A (power consumption of 120 W).

Open the console box lid and open the lid.

Note:

The power outlet can be used when

The power switch is in ACC or ON.

When stopping the hybrid system

Disconnect electrical devices with charging functions, such as mobile battery packs.If such devices are left connected, the hybrid system may not stop normally.

Notice:

To prevent the fuse from being blown

Do not use an accessory that uses more than 12 V 10 A.

To avoid damaging the power outlet

Close the power outlet lid when the power outlet is not in use. Foreign objects or liquids that enter the power outlet may cause a short circuit.

To prevent 12-volt battery discharged

Do not use the power outlet longer than necessary when the hybrid system is off.

Sun visorsSun visors

To set the visor in the forward position, flip it down.

To set the visor in the side position, flip down, unhook, and swing it to the side.

To use the side extender, place the visor in the side position, then slide it backward.

Vanity mirrors

Vanity lights

Mirrors Vanity mirrors

Lights Vanity lights Vanity mirrors

Slide the cover to open.

The vanity light turns on.

Note:

To prevent 12-volt battery discharge

If the vanity lights remain on when the power switch is OFF, the lights will go off automatically after 20 minutes.

Notice:

To prevent the 12-volt battery from being discharged

Do not leave the vanity lights on for extended periods while the hybrid system is off.

ArmrestArmrest

Fold down the armrest for use.

Notice:

To prevent damage to the armrest

Do not apply too much load on the armrest.

Assist gripsAssist grips

An assist grip installed on the ceiling can be used to support your body while sitting on the seat.

Warning:

Assist grip

Do not use the assist grip when getting in or out of the vehicle or rising from your seat.

Notice:

To prevent damage to the assist grip

Do not hang any heavy object or put a heavy load on the assist grip.

Hooks Coat hooks

Coat hooksCoat hooks

The coat hooks are provided with the rear assist grips.

Warning:

Items that cannot be hung on the coat hook

Do not hang coat hangers or other hard or sharp objects on the hook. If the SRS curtain shield airbags deploy, these items may become projectiles, causing death or serious injury.