Light bulbs You may replace the following bulbs yourself. The difficulty level of replacement varies depending on the bulb. If necessary bulb replacement seems difficult to perform, contact your Toyota dealer. For more information about replacing other light bulbs, contact your Toyota dealer. Preparing for light bulb replacement Check the wattage of the light bulb to be replaced. (Light bulbs) Bulb locations Front Front side marker lights (bulb type) Front turn signal/parking lights (vehicles without side turn signal lights) Rear Back-up lights Rear turn signal lights Rear side marker lights (bulb type) Bulbs that need to be replaced by your Toyota dealer Headlights/daytime running lights Parking lights (vehicles with side turn signal lights) Front turn signal lights (vehicles with side turn signal lights) Front side marker lights (LED type) LED accent lights (if equipped) Side turn signal lights (if equipped) Tail lights Stop lights Rear side marker lights (LED type) High mounted stoplight License plate lights Note: Headlights/daytime running lights Replacing light bulbs Parking lights Replacing light bulbs Turn signal lights Replacing light bulbs Front turn signal lights Replacing light bulbs LED accent lights Replacing light bulbs Side turn signal lights Replacing light bulbs Tail lights Replacing light bulbs Stop lights Replacing light bulbs Rear side marker lights Replacing light bulbs Lights Replacing light bulbs High mounted stoplight Replacing light bulbs License plate lights Replacing light bulbs LED light bulbs The lights other than the front turn signal lights/parking lights (vehicles without side turn signal lights), front side marker lights (bulb type), rear turn signal lights, rear side marker lights (bulb type) and back-up lights consist of a number of LEDs. If any of the LEDs burn out, take your vehicle to your Toyota dealer to have the light replaced. Condensation build-up on the inside of the lens In certain situations, such as when driving in the rain or when washing the vehicle, condensation may form on the inner side of the headlight lens and other lights. As each light has a ventilation hole, moist air may enter. If the ambient temperature is low, condensation may form temporarily, but it will dissipate as the inside of the light is warmed up. As the condensation is due to a phenomenon similar to windows fogging in the rain, it does not indicate a malfunction. Contact your Toyota dealer for more information in the following situations: Large drops of water have built up on the inside of the lens. Water has built up inside the headlight. When replacing light bulbs When replacing light bulbs Replacing light bulbs Front turn signal/parking lights Replacing light bulbs Front turn signal/parking lights (vehicles without side turn signal lights) Turn the bulb base counterclockwise. Type A Type B Remove the light bulb. Type A Type B When installing, reverse the steps listed. Front side marker lights Replacing light bulbs Side marker lights Replacing light bulbs Front side marker lights (bulb type) Turn the bulb base counterclockwise. Remove the light bulb. When installing, reverse the steps listed. Rear turn signal lights Replacing light bulbs Rear side marker lights Replacing light bulbs Side marker lights Replacing light bulbs Rear turn signal lights and rear side marker lights (vehicles with blub type rear side marker lights) Open the trunk lid. Insert a flathead screwdriver between the cover and the light assembly and pry up the cover to disengage the claws (indicated by a dotted line). To prevent scratching the vehicle, wrap the tip of the flathead screwdriver with a cloth, etc. Pull the cover toward the rear of the vehicle and remove the cover. Remove the 2 screws and then remove the light assembly by pulling it straight back. Turn the bulb base counterclockwise. Rear side marker lights Rear turn signal lights Remove the light bulb. Rear side marker lights Rear turn signal lights When installing the light bulb, install it by conducting steps 6 and 5 with the directions reversed. Install the light assembly and then install the 2 screws. Align the guide and pin on the light assembly with the mounting when installing it. Install the cover. Rear turn signal lights Replacing light bulbs Rear turn signal lights (vehicles with LED type rear side marker lights) Open the trunk lid. Insert a flathead screwdriver between the cover and the light assembly and pry up the cover to disengage the claws (indicated by a dotted line). To prevent scratching the vehicle, wrap the tip of the flathead screwdriver with a cloth, etc. Pull the cover toward the rear of the vehicle and remove the cover. Remove the 2 screws and then remove the light assembly by pulling it straight back. Turn the bulb base counterclockwise. Remove the light bulb. When installing the light bulb, install it by conducting steps 6 and 5 with the directions reversed. Install the light assembly and then install the 2 screws. Align the guide and pin on the light assembly with the mounting when installing it. Install the cover. Back-up lights Replacing light bulbs Back-up lights Open the trunk lid, remove the clips, and pull back the cover. Turn the bulb base counterclockwise and remove it. Remove the light bulb. When installing, reverse the steps listed. Warning: Replacing light bulbs Turn off the lights. Do not attempt to replace the bulb immediately after turning off the lights. The bulbs become very hot and may cause burns. Do not touch the glass portion of the light bulb with bare hands. When it is unavoidable to hold the glass portion, use and hold with a clean dry cloth to avoid getting moisture and oils on the bulb. Also, if the bulb is scratched or dropped, it may blow out or crack. Fully install light bulbs and any parts used to secure them. Failure to do so may result in heat damage, fire, or water entering the light unit. This may damage the lights or cause condensation to build up on the lens. To prevent damage or fire Make sure bulbs are fully seated and locked.